Course detail
Experimental Methods and Instruments
FSI-IEP Acad. year: 2027/2028 Winter semester
The course covers the measurement of basic physical and process quantities in energy engineering and technical practice. It starts with metrology, measurement errors and uncertainty. It then covers the principles, properties and limits of sensors for temperature, pressure, flow and level, vibration diagnostics, analytical methods (mass spectrometry, thermogravimetry), and emission measurement and gas detection. The final part deals with A/D converters, signal processing and data acquisition systems.Lectures explain measurement principles using practical examples and worked problems. Exercises have two parts. In part A, each student individually completes two laboratory tasks, a temperature sensor and a gas sensor, on an Arduino electronic kit: the student writes the measurement program, processes the data and evaluates the uncertainty in Python and LabVIEW. In part B, students visit the institute's laboratories (e.g. vortex tube, fluidised bed, thermogravimetric analyser, 3D scanner, optical microscope).
Language of instruction
Czech
Number of ECTS credits
5
Supervisor
Department
Learning outcomes of the course unit
By completing this course, students will gain knowledge of:
- metrology and uncertainty: explain basic metrological terms (precision, trueness, repeatability), the SI after the 2019 redefinition,types of measuring instruments, the difference between calibration and verification and the expression of measurement uncertaintyaccording to GUM (type A, type B, combined and expanded),
- temperature: describe resistance sensors (RTD, Pt100/Pt1000, 2- to 4-wire connection, self-heating), thermocouples (types,cold-junction compensation, compensating cables), thermistors and non-contact measurement (pyrometers, thermography, emissivity)and their use in energy engineering (steam and feedwater in thermowells, flue gas and combustion chamber, equipment surfaces andinsulation),
- pressure: describe elastic pressure gauges (Bourdon tube, diaphragm), electrical sensors (strain-gauge, piezoresistive, capacitive,resonant) and 4–20 mA smart transmitters for absolute, gauge and differential pressure, their installation (siphon, diaphragm seal) anduse in energy engineering (steam and water pressure, flue draught, differential pressure across orifices and filters),
- flow: describe differential pressure devices (orifice, nozzle, Venturi tube), volumetric, turbine, electromagnetic, ultrasonic, vortex,Coriolis and thermal flowmeters and velocity probes, and match them to applications in energy engineering (steam – orifice, nozzle,vortex; water – electromagnetic, ultrasonic; natural gas and fuels – turbine, Coriolis; combustion air and flue gas – velocity probes; heatmetering),
- level: describe hydrostatic, float, capacitive, ultrasonic and radar level gauges and their use (boiler drum, feedwater tank, fuel storage),
- vibration diagnostics of turbines and turbocompressors: describe vibration quantities and sensors (accelerometers, non-contactprobes for relative shaft vibration X–Y, axial position and phase reference), absolute versus relative vibration, turbine-generatormonitoring, evaluation zones A–D (ISO 20816), spectra and shaft orbits, and typical causes of vibration (unbalance, misalignment,looseness, bearings, critical speeds, surge) and the principles of rotor balancing,
- analytical methods and gas analysers: describe the principle of mass spectrometry (ionisation, ion separation by m/z) andthermogravimetry (incl. coupling with MS and SMPS) in fuel analysis, flue gas analysers (infrared NDIR, TDLS and FTIR, fluorescence forSO2, chemiluminescence for NOx, paramagnetic and electrochemical for O2) and semiconductor gas sensors, and their use in emissionmeasurement and combustion control,
- A/D converters: explain sampling, the Nyquist criterion, aliasing and the anti-aliasing filter, quantisation, LSB, ENOB, describe the architectures (flash, SAR, integrating, sigma-delta, pipeline), the criteria for choosing them (temperature andpressure – sigma-delta, vibration – SAR) and the role of FPGAs,data acquisition systems: describe the structure of a data acquisition system (sensor, transmitter, 4–20 mA signal, data logger,recording and transmission).
Entry knowledge
Knowledge from the first four semesters of the bachelor's programme at the Faculty of Mechanical Engineering; in particular, the student can:
- use basic physical quantities and SI units and convert between them,describe the basic laws of thermodynamics,
- heat transfer and fluid mechanics (state variables, Bernoulli equation, heat balance),
- describe basic electric circuits and quantities (voltage, current, resistance),
- calculate basic statistical characteristics of a data set (mean, standard deviation) and work with a spreadsheet.
Rules for evaluation and completion of the course
The course ends with a course-unit credit and an examination. The credit is a prerequisite for the examination. Points from the credit count towards the final grade: credit max. 40 points, examination max. 60 points, total 100 points.
Attendance and checks. Attendance at lectures is recommended. Attendance at all exercises (parts A and B) is compulsory and is recorded.
Credit requirements (max. 40 points, minimum 20 points):
- attendance at all exercises,individual completion of two laboratory tasks A: the student builds a measurement chain using an Arduino electronic kit with atemperature sensor (A1) and with a gas sensor (A2),
- writes the measurement program, processes the measured data and evaluates themeasurement uncertainty in Python and LabVIEW,
- for each task, the student submits a report in e-learning no later than 14 days after the task;
- each task is scored 0–20 points,at least 20 of 40 points are required for the credit.
The credit must be obtained by the end of the examination period.
Examination (max. 60 points, minimum 30 points) is written.
The written test contains theoretical questions and calculation problems covering the whole lecture syllabus, e.g. measurement uncertainty or A/D converter parameters. The student is entitled to one resit.
The final grade is the sum of points for the credit and the examination (max. 100) according to the ECTS scale.
Aims
Skills:
select a suitable sensor for a given measurement task and justify the choice with respect to range, accuracy and operating conditions,determine type A and type B uncertainties and the combined uncertainty of directly and indirectly measured quantities,calculate basic A/D converter parameters (quantisation step, SNR, aliasing) and select the converter type and sampling frequency,build a measurement chain with a sensor and an Arduino kit, write the program, calibrate the sensor, record data and evaluateuncertainty in Python and LabVIEW,evaluate the time constant of a sensor from measured data,assess the condition of a rotating machine from its vibration level and identify the likely cause from the spectrum,independently write a technical report on a laboratory task.
The study programmes with the given course
Programme B-ENE-P: Energy, Bachelor's, compulsory
Type of course unit
Lecture
26 hours, optionally
Syllabus
1. Fundamentals of measurement, metrology, measurement errors and uncertainty.
2. Temperature measurement I – expansion, resistance and semiconductor sensors.
3. Temperature measurement II – thermocouples, non-contact measurement, time constant.
4. Pressure measurement.
5. Flow measurement I – volumetric, differential pressure, ultrasonic and electromagnetic meters.
6. Flow measurement II – mass flowmeters, velocity probes.
7. Level measurement.
8. Vibration diagnostics of turbines and turbocompressors.
9. Analytical methods and instruments (MS, TGA).
10. A/D converters – sampling, quantisation, architectures, FPGA.
11. Data acquisition systems.
12. Emissions and flue gas analysers.
13. Summary and review.
Laboratory exercise
26 hours, compulsory
Syllabus
1. Introduction, safety, task assignment.
2. Task A1 – temperature sensor: Arduino setup, program, measurement.
3. Task A1 – temperature sensor: data processing and uncertainty (Python, LabVIEW).
4. Task A2 – MQ gas sensor: Arduino setup, program, calibration.
5. Task A2 – MQ gas sensor: measurement, data processing and uncertainty (Python, LabVIEW).
6. Laboratory B – vortex tube.
7. Laboratory B – fluidised bed.
8. Laboratory B – thermogravimetric analyser.
9. Laboratory B – 3D scanner.
10. Laboratory B – optical microscope.
11. Laboratory B – as available.
12. Consultations on reports.
13. Make-up session, credit.